Search found 853 matches

by angusgr
Thu May 26, 2016 2:06 am
Forum: EtherTen
Topic: USB driver problem
Replies: 7
Views: 7085

Re: USB driver problem

So none of these three units are working with your computer? Do they work with other computers?

I'm afraid it sounds like it might be a problem with the computer's USB host hardware or drivers.
by angusgr
Thu May 26, 2016 2:05 am
Forum: Module Discussion
Topic: Relay8 Esp8826 12-E I2C connection.
Replies: 10
Views: 9640

Re: Relay8 Esp8826 12-E I2C connection.

Hi cesco,

Sorry about the delay updating the web site. The relay driver shield is designed to act as drivers to switch a relay coil, they aren't relays themselves. If you buy a relay and drive it from the relay driver shield, you can switch much higher currents like a 1A LED.

by angusgr
Wed May 18, 2016 7:20 am
Forum: BTSH: Bluetooth Shield
Topic: Bluetooth master slave connection
Replies: 2
Views: 10587

Re: Bluetooth master slave connection

Hi vijay, Please only send queries via the forum or email, we read both. :) I've replied to you via email, but I'm going to copy part of the response here for anyone who is interested: Try swapping the position of the '?' and the ' ' ie: AT+RNAME? 2015,4,90245 (If this doesn't work, try also omittin...
by angusgr
Wed May 18, 2016 7:11 am
Forum: LCDK: LCD & Keypad Shield
Topic: LCD & Keypad shield question.
Replies: 5
Views: 11983

Re: LCD & Keypad shield question.

Hi aus_sparky,

Your code looks good, the switch statement is probably the right one to use.

It looks like you might be missing a "case" statement between BUTTON_DOWN and BUTTON_UP, inside the switch.

by angusgr
Wed May 18, 2016 7:09 am
Forum: LeoStick
Topic: Leostick and GPS module
Replies: 2
Views: 5669

Re: Leostick and GPS module

Hi Jason, The LeoStick has both USB/Serial (embedded USB) and a hardware serial port, so you can connect the GPS module to the RX & TX pins (RX=D0, TX=D1). In your sketch, "Serial" is the USB connection to the computer. Use Serial1 for the RX & TX pins. More information can be found here: https://ww...
by angusgr
Wed May 18, 2016 6:50 am
Forum: EtherTen
Topic: Serial for debugging
Replies: 2
Views: 3496

Re: Serial for debugging

Hi Matt,

Yes! Pins 0 & 1 are TX and RX. If you connect these to your 5V serial adapter, plus a ground pin between the two, then you can communicate directly as if you were connected to the USB port.

by angusgr
Mon May 09, 2016 4:25 am
Forum: LeoStick
Topic: Turning off the blue power LED in software?
Replies: 2
Views: 4247

Re: Turning off the blue power LED in software?

Hi Alfie,

Unfortunately you can't disable it from software. The easiest option is to place some black tape over the entire LED, if you don't mind losing the TX/RX light as well.

by angusgr
Mon May 09, 2016 4:21 am
Forum: Eleven
Topic: Experiment 3 (digial input)
Replies: 4
Views: 7632

Re: Experiment 3 (digial input)

Hi Salispahic,

Are you able to post a photo of your setup, please? Also, have you checked the code in the Arduino IDE that you've uploaded to the Eleven board?


by angusgr
Tue May 03, 2016 6:14 am
Forum: Module Discussion
Topic: IRTemp example not working
Replies: 7
Views: 5816

Re: IRTemp example not working

Interalia wrote:Same issue, no wires soldered on, Arduino 1.6.8
Sorry to hear the IRTemp isn't working properly. If you've tried everything mentioned in this thread then please contact us at the support email listed above.
by angusgr
Tue May 03, 2016 6:12 am
Forum: Dot Matrix Display
Topic: New beta release "DMD2" Library
Replies: 115
Views: 86442

Re: New beta release "DMD2" Library

RuralGeek, are you able to post your sketch code for me to take a look at?